بازگشت

این کالا را با دوستان خود به اشتراک بگذارید

ماژول تست ظرفیت باتری لیتیوم یون ZB2L3

موجودی ها در سایت به روز می باشد درصورت نیاز به پشتیبانی لطفا از طریق تلگرام با آی دی @micro_sib پیام خود را ارسال کنید تا در اولین فرصت به درخواست شما رسیدگی شود. با تشکر
از ساعت 9 الی 16 پاسخ گوی شما هستیم
امکان برگشت کالا در همه گروه ها با دلیل "انصراف از خرید" تنها در صورتی مورد قبول است که پلمپ کالا باز نشده باشد.
گارانتی اصالت و سلامت فیزیکی کالا
ناموجود
114,800 تومان

ناموجود

توضیحات بیشتر

مقاومت موجود در پکیج تنها جهت تست موقت ماژول است. جهت تست بلند مدت نیاز به مصرف کننده مطمئن خواهید داشت.
Features:
Power supply voltage: DC4.5-6V (micro USB connector)
Operating current: Less than 70mA
Discharge voltage: 1.00V-15.00V, 0.01V resolution
Termination voltage range: 0.5-11.0V
Supported current: Maximum 3.000A, 0.001A resolution
Maximum voltage measurement error: 1% + 0.02V
Maximum current measurement error: 1.5% ± 0.008A
Maximum battery capacity range: 9999Ah (1Ah = 1000mAh) greater value is switched by shifting the decimal point, when it is less than 10Ah will display X.XXX, up to 10Ah or more will display XX.XX, and so on.
Board size: 50 x 37mm
Finished size: 50 x 37 x 17mm (L x W x H maximum position size, contains copper foot height)
Board net weight: 28g (including pillars)
Resistor weight: about 27g (including cable)
How to use:
1. The battery under test should be fully charged first.2. Connect the positive pole of the battery under test to the input positive, the negative pole to the input negative pole, and the reverse polarity (the reverse may damage the circuit)! Connect the load to the output positive and output negative, and give the tester micro USB working power (please use the mobile phone charging head, do not use desktop or notebook USB power supply), the battery voltage is displayed at this time.3. To start the test directly, just press the “OK” button, the tester can automatically set the appropriate termination voltage according to the battery’s full charge voltage and will flash the display 3 times to start the test. Need to manually set the termination voltage only need to press the “+” or “-” button to modify the battery voltage display state, the termination voltage is displayed as the beginning of the flashing “E”, the latter represents the voltage value, the resolution is 0.1V, after setting Press “OK” to start the test.4. After the test starts, the tester will turn on the electronic switch that controls the load. The test process data will be displayed in turn in the following order: current-voltage (V), current discharge current (A), released capacity (Ah), discharge time (Min) ), the termination voltage E (V), you can manually switch the value by pressing the “+” and “-” buttons. When the battery voltage is lower than the termination voltage, the tester cuts off the load, and the display data stays on the capacity (Ah) and flashes rapidly with the “Ah” indicator. The capacity displayed at this time is the actual discharge capacity of the battery. Press any button. The data can be displayed stably. After that, press the “+” and “-” buttons to check the termination voltage, average voltage, average current, capacity, and discharge time. Press the “OK” button again to return to the power-on state to replace the battery test. 

ادامه مطلب

نقد و بررسی‌ها افزودن نظر

4.3
از ۵
از مجموع 3 امتیاز
  • کیفیت ساخت
    3
  • ارزش خرید به قیمت
    3
  • نوآوری
    3
  • امکانات
    3
  • سهولت استفاده
    3
  • طراحی و ظاهر
    3
دیدگاه خود را درباره این کالا بیان کنید
افزودن دیدگاه
بدون عنوان
17 تیر 1401 نیما
سلام خسته نباشید اگه یه سری از لازم سایت دوباره شارژ شه خیلی خوب میشه
آیا این دیدگاه برایتان مفید بود؟
0
بدون عنوان
10 تیر 1401 حسین
سلام و خسته نباشید فراوان از شما
بعد از کلی جست و جو بالاخره با بهترین قیمت پیدا کردم!
همون مقاومت های آجری همراهش کفایت میکنه البته با یه هیت سینک بزرگ
1 دونه = 500 ma جریان کشی
هر دوتا به صورت موازی = 1 A جریان کشی
آیا این دیدگاه برایتان مفید بود؟
0
بدون عنوان
23 فروردین 1401 عماد
ماژول جمع و جور و کار راه اندازی هست ولی دقت اندازه گیریش اونطوری که در مشخصاتش عنوان شده نیست.مخصوصا خطای اندازه گیری جریانش برای جریان های زیر نیم آمپر خیلی زیاد هست.مد کالیبراسیون هم داره که برای من درست کار نکرد و ماژول عملا از کار افتاد.در کل برای مقایسه چند باطری با هم دیگه مناسب هست در غیر اینصورت خریدش را توصیه نمیکنم
آیا این دیدگاه برایتان مفید بود؟
0
ماژول تست ظرفیت باتری لیتیوم یون ZB2L3
ماژول تست ظرفیت باتری لیتیوم یون ZB2L3
گارانتی اصالت و سلامت فیزیکی کالا
ناموجود
114,800 تومان

ناموجود